Breakaway Dam and Evanston Project Updates
Released
Released
Announcement PDF
Page 1
Breakaway Dam and Evanston Project Updates
HIGHLIGHTS
➢ Planning for follow-up drilling program finalised, including approximately 3,000
metres of RC drilling, to test high-priority EM conductors, expand the Central Zone
and assess additional targets at Breakaway Dam
➢ 2025 drilling and geophysical programs have confirmed Breakaway Dam as a copper-
rich Volcanogenic Massive Sulphide (VMS) system1
➢ Previous drilling and DHEM1
have defined ~700 metres of sulphide-bearing strike, with
mineralised horizons averaging ~10 metres estimated true width including:
o 9.2 m @ 0.48% Cu (estimated true width 8.7 m), including higher-grade intervals of
0.95 m @ 1.18% Cu and 1.7 m @ 1.05% Cu (BDCDD2501)
o 1.47 m @ 1.97% Cu and 0.24% Zn (estimated true width 1.4 m) (BDCDD2502)
o 4.2 m @ 0.32% Cu and 0.29% Zn (estimated true width 4.1 m) (BDCDD2504)
➢ Multiple strong DHEM conductors identified, including one plate that remained
untested, supporting further follow-up drilling
➢ Land position expanded at Breakaway Dam, with additional tenements acquired and
further applications progressed over prospective ground aligned with the confirmed
VMS system
➢ Central Yilgarn Drilling Phase 1 assay results from Leghorn confirms the mafic host
sequence, mineralisation orientation with results including:
o 1m @ 2.93 g/t Au from 159m (end of hole) (25EVRC009)
o 2m @ 1.01 g/t Au from 161m in (25EVRC007)
Catalina Resources Limited (“Catalina” or “the Company”) is pleased to report it has developed the next
stage of exploration at its Breakaway Dam Project, following confirmation that the system represents a
copper-rich Volcanogenic Massive Sulphide (VMS) system, located approximately 17 km east of Menzies
in Western Australia (figure 1).
The forward exploration program has been advanced as a priority following the outcomes, conclusions
and recommendations of the recently completed 2025 drilling and geophysical campaign, which
confirmed Breakaway Dam as a well-developed VMS system with demonstrated scale and multiple
untested targets.
Executive Director, Ross Cotton, commented:
“The discovery of a VMS system at our newly acquired Breakaway Dam Project is critically important to
our exploration strategy, as it indicates the potential presence of high-value, high-grade, multi-
commodity ore deposits.
ASX Announcement
3 February 2026
Page 2
We have aclearpathwayto guidefurther works atthis highly prospective asset.This is bolstered by Board
expertise and past success in leading the discovery,development and operation of a prolific copper-gold
operation in Western Australia, putting Catalina in good stead to capitalise on this emerging
opportunity."
Figure 1. Breakaway Dam Regional Location
SUMMARY OF RECENT DRILLING RESULTS1
Recent drilling1
confirms a classic VMS architecture at Breakaway Dam, characterised by:
➢ Sulphide mineralisation intersected over approximately 700 metres of strike, with mineralised
horizons averaging ~10 metres estimated true width
➢ Copper-dominant sulphide mineralisation, with individual intervals returning grades of up to
~2% Cu, noting that peak grades and widths do not coincide
➢ Clear metal zoning, with copper- and zinc-rich sulphides developed above basaltic host rocks
and associated footwall stringer zones
➢ Multiple strong DHEM conductors, including one that remains only partially tested
➢ A structural and metamorphic overprint that has compressed the original massive sulphide
horizons
Drilling intersected copper- and zinc-bearing sulphide mineralisation across multiple holes, with
intervals ranging from narrow high-grade lenses to broader zones of moderate-grade mineralisation.
Significant intersections included:
➢ 9.2 m @ 0.48% Cu (estimated true width 8.7 m), including higher-grade intervals of 0.95 m @
1.18% Cu and 1.7 m @ 1.05% Cu (BDCDD2501)
Page 3
➢ 1.47 m @ 1.97% Cu and 0.24% Zn (estimated true width 1.4 m) (BDCDD2502)
➢ 4.2 m @ 0.32% Cu and 0.29% Zn (estimated true width 4.1 m) (BDCDD2504)
Two of the most VMS-anomalous drill holes occur approximately 500 metres and a further 700 metres
northwest along strike, within an area that remains extremely lightly drilled based on available
historical datasets.
This sparse distribution highlights potential for additional sulphide development outside the currently
defined central zone and has been incorporated into forward targeting considerations.
Collectively, these intersections, when integrated with DHEM responses, support the interpretation of
a zoned VMS system with both disseminated and more massive sulphide components, and provide a
clear technical basis for prioritising follow-up drilling on untested conductors and along strike.
Next Phase Exploration Program
Catalina has now finalised a structured follow-up exploration program aimed at testing the most
prospective components of the system while continuing to expand the known footprint.
Catalina is actively engaging drilling contractors, with the intention to commence drilling immediately
upon securing rigs. The program will proceed under existing PoW approvals, and heritage clearances
have already been completed.
Key elements of the next phase include:
➢ Targeted drilling of untested high-conductance EM plates proximal to BDCDD2503 (figure 2),
prioritising the strongest and least tested conductors
➢ ~2,000 metres of systematic RC drilling across the BDC Central Zone (figure 2) to assess grade
continuity beyond current EM-defined targets
➢ Approximately ~1,000 metres of RC drilling and follow-up DHEM to evaluate potential
mineralisation beneath shallow historical drilling within the broader project area
➢ First-pass drilling of an additional target where coincident geochemical anomalies and
magnetic lows are interpreted as indicative of a potential feeder position
Page 4
Figure 2. Plan view of BDC Central Zone target drill area and previous drill holes and associated results1
.
This next phase of drilling is designed to systematically test the highest-priority conductors and
geological positions identified to date, while continuing to evaluate the scale and continuity of
mineralisation across the Breakaway Dam system.
Results from this program will be used to refine the Company’s geological model, prioritise follow-up
targets and inform subsequent exploration activities. Catalina will provide further updates as drilling
commences and results become available.
TENEMENT CONSOLIDATION AND LAND POSITION
In parallel with advancing exploration at Breakaway Dam, Catalina is progressing applications for
additional Exploration Licences over unpegged ground adjacent to the existing tenure, with the
objective of securing a coherent and contiguous land position across this prospective structural
corridor.
These are considered complementary to E29/1037 and are interpreted to cover prospective
stratigraphic and structural positions consistent with the geological architecture observed at
Breakaway Dam.
This tenement consolidation strategy is intended to provide Catalina with the flexibility to
systematically evaluate the broader mineral system, efficiently follow up exploration results, and
support the continued advancement of the Breakaway Dam Project.
Page 5
PHASE 1 RC DRILLING RESULTS – CENTRAL YILGARN PROJECT
LEGHORN PROSPECT, EVANSTON PROJECT
Catalina is also pleased to provide an update on results from the Phase 1 RC drilling program at the
Leghorn Prospect, part of the Evanston Project within the Central Yilgarn Gold District of Western
Australia.
These results form part of an ongoing Phase 1 drilling campaign totalling ~10,000m of RC and Aircore
drilling across the Central Yilgarn Project2
, with drilling and assay results from multiple targets still
pending.
The Phase 1 program was undertaken prior to the Christmas period and formed the initial focus of
Catalina’s broader Central Yilgarn drilling campaign. Drilling was designed to follow up and test the
continuity of previously reported anomalous gold mineralisation intersected in historic drilling.
Executive Director, Ross Cotton, commented:
“The Leghorn results provide useful confirmation of the geological and structural model we set out to
test, particularly in relation to host lithology and mineralisation orientation. While Leghorn represents
only one component of the broader Central Yilgarn program, the information gained is being
incorporated into ongoing targeting as Phase 1 drilling continues across Evanston and Yerilgee, with
further results pending.”
Drilling Summary – Leghorn Prospect
Results reported here relate specifically to drilling completed at the Leghorn Prospect, one of several
targets included within the Phase 1 program.
The Phase 1 RC drilling program at the Leghorn Prospect comprised 8 RC drill holes for a total of 1,521
metres. Drilling targeted along-strike extensions of gold mineralisation intersected in earlier drilling,
including broad zones of anomalous mineralisation reported in historic drill hole BARRC007 which
provide previous results of:
➢ 48m @ 0.6g/t Au (incl. 21m @ 1.3g/t Au) and 3m @2.28g/t Au (BARRC007)3
Geological Observations and Results
Drilling intersected a mafic stratigraphic sequence comprising basalt, amphibolite, and mafic schists,
consistent with the geological interpretation previously reported for the Evanston Project.
Gold mineralisation is interpreted to be hosted within this mafic sequence and to dip approximately 40
degrees to the east, providing confidence in the orientation of the mineralised system and informing
future drill design.
Drilling along strike has confirmed the interpreted mineralisation model, with intersections including:
• 1m @ 2.93 g/t Au from 159m (end of hole) in 25EVRC009
• 2m @ 1.01 g/t Au from 161m in 25EVRC007
These results confirm continuity of gold mineralisation along strike and at depth and support the
interpretation of a coherent mineralised system at the Leghorn Prospect.
Page 6
Significant Intersections (>0.5g/t Au) and Interpretation
Hole Id
Depth
From (m)
Depth To
(m)
Width
(m)
Gold
(g/t)
Significant intersection
25EVRC001 183 184 1 1.29 1m @ 1.29g/t Au from 183m
25EVRC007 161 163 2 1.01 2m @ 1.01g/t Au from 161m
25EVRC009 159 160 1 2.93 1m @ 2.93g/t Au from 159m
25EVRC010 20 21 1 1.3 1m @ 1.3g/t Au from 20m
25EVRC011 60 61 1 0.66 1m @ 0.66g/t Au from 60m
25EVRC011 81 82 1 0.94 1m @ 0.94g/t Au from 81m
25EVRC011 130 131 1 0.71 1m @ 0.71g/t Au from 130m
25EVRC012 8 9 1 0.56 1m @ 0.56g/t Au from 8m
The interpreted mineralised zone is developed within a mafic stratigraphic sequence and exhibits
continuity along strike, consistent with the geological model tested during the Phase 1 drilling program.
Drill hole locations, significant gold intersections, and projected mineralised trends are shown to
provide spatial context for reported results.
This interpretation provides a framework for refining follow-up drill targeting and assessing the broader
potential of the Leghorn Prospect within the Evanston Project area.
Figure 5. View of the Leghorn Prospect illustrating the interpreted extent and orientation of gold mineralisation
based on Phase 1 RC drilling, historical drilling data, and current geological interpretation
Representative RC Rock Chip Images
Rock chip observations, supported by geological logging, indicate that gold mineralisation is
predominantly hosted within amphibolite and biotite schist units. The images are not indicative of
grade, tenor, or continuity of mineralisation, but assist in demonstrating the geological setting,
alteration styles, and structural characteristics relevant to ongoing interpretation and follow-up
targeting.
Page 7
Hole Id Figure
Number
Depth From
(m)
Depth
To (m)
Gold
(g/t)
Geological observations
25EVRC001 6 183 184 1.29
Amphibolite with blebby
pyrite localised within quartz
veins and silica replacement
25EVRC007 7 161 163 1.01
Heavily silica altered
amphibolite
25EVRC009 8 159 160 2.93
Amphibolite-biotite schist
zone
Figure 6. Representative RC rock chip samples from drill hole 25EVRC001 (183–184 m), Leghorn Prospect
Figure 7. Representative RC rock chip samples from drill hole 25EVRC007 (161–163 m), Leghorn Prospect
Figure 8. Representative RC rock chip samples from drill hole 25EVRC009 (159–160 m), Leghorn Prospect
Page 8
Ongoing Phase 1 Drilling and Assay Status
Phase 1 drilling of approximately ~10,000 metres of combined AC and RC drilling is continuing across
the Evanston and Yerilgee Projects, with multiple target zones tested as part of the current campaign.
Assay results from all other Phase 1 target areas are currently pending, with samples submitted to the
laboratory. These results will be reported progressively as they are received, validated, and interpreted.
Catalina considers the Leghorn results to represent one component of a broader, active exploration
program, with further updates expected as the Phase 1 campaign continues.
Contacts
Investors/ Shareholders
Ross Cotton
Executive Director
T: +61 (0)8 6165 8858
REFERENCES (ASX)
This Report contains information extracted from ASX market announcements reported in accordance
with the 2012 edition of the “Australasian Code for Reporting of Exploration Results, Mineral Resources
and Ore Reserves” (“2012 JORC Code”). Further details (including 2012 JORC Code reporting tables
where applicable) of exploration results referred to in this announcement can be found in the following
announcements lodged on the ASX:
1. Refer CTN ASX announcement 20 January 2026 Drilling-Confirms-Breakaway-Dam-as-a-
CopperRich-VMS-System.pdf
2. Refer CTN ASX announcement 1 December 2025 Phase-1-Drilling-at-Evanston-Underway.pdf
3. Refer CTN ASX announcement 11 December 2025 Acquisition of Central Yilgarn
4. Refer FRS ASX announcement 18 November 2025 Drilling Completed at Breakaway Dam VMS
Prospect
COMPETENT PERSONS STATEMENT
Newly reported information in this announcement that relates to exploration activities within the Yilgarn
Project is based on information compiled by Dr Nishka Piechocka, PhD, Vice President of the Australian
Institute of Geoscientists (AIG) and a full-time employee of Catalina Resources Limited. Dr Piechocka
has sufficient experience relevant to the style of mineralisation and type of deposit under consideration
and to the activity being undertaken to qualify as a Competent Person as defined in the 2012 Edition of
the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC
Code). Dr Piechocka consents to the inclusion in the report of the matters based on her information in
the form and context in which it appears.
Where the Company refers to the Mineral Resources in this report (referencing previous releases made
to the ASX), it confirms that it is not aware of any new information or data that materially affects the
information included in that announcement and all material assumptions and technical parameters
Page 9
underpinning the Mineral Resource estimate with that announcement continue to apply and have not
materially changed.
FORWARD-LOOKING STATEMENTS
This announcement contains forward-looking statements that are subject to a range of risks and
uncertainties. These statements relate to the Company’s expectations, intentions, or strategies
regarding the future. These statements can be identified by the use of words like “anticipate”, “believe”,
“intend”, “estimate”, “expect”, “may”, “plan”, “project”, “will”, “should”, “seek” and similar words or
expressions containing same. These forward-looking statements reflect the Company’s views and
assumptions with respect to future events as of the date of this release and are subject to a variety of
unpredictable risks, uncertainties, and other unknowns. Actual and future results and trends could
differ materially from those set forth in such statements due to various factors, many of which are
beyond our ability to control or predict. These include, but are not limited to, risks or uncertainties
associated with the acquisition and divestment of projects (including risks associated with completing
due diligence and, if favourable results are obtained, proceeding with the acquisition of the Beasley
Creek Project), joint venture and other contractual risks, metal prices, exploration, development and
operating risks, competition, production risks, sovereign risks, regulatory risks including environmental
regulation and liability and potential title disputes, availability and terms of capital and general
economic and business conditions.
Given these uncertainties, no one should place undue reliance on any forward-looking statements
attributable to the Company, or any of its affiliates or persons acting on its behalf. Subject to any
continuing obligations under applicable law the Company disclaims any obligation or undertaking to
disseminate any updates or revisions to any forward-looking statements in this announcement to reflect
any change in expectations in relation to any forward-looking statements or any change in events,
conditions or circumstances on which any such statement is based.
ABOUT CATALINA RESOURCES LIMITED
Catalina Resources Limited is an Australian diversified mineral exploration and mine development
company whose vision is to create shareholder value through the successful exploration of prospective
gold, base metal, lithium and iron ore projects and the development of these projects into production.
Page 10
APPENDIX 1: DRILLHOLE SPECIFICATIONS
Hole Id Type Easting
(GDA94z51)
Northing
(GDA94z51)
Elevation
(m)
Dip (⁰) Azi (⁰) Actual
Depth
(m)
25EVRC001 RC 181276 6721029 446 -61 267 250
25EVRC006 RC 181132 6721028 443 -62 266 154
25EVRC007 RC 181081 6721029 441 -60 270 323
25EVRC008 RC 181175 6720830 442 -60 270 154
25EVRC009 RC 181250 6720830 442 -60 270 160
25EVRC010 RC 181069 6721138 442 -60 270 172
25EVRC011 RC 181144 6721140 446 -60 270 154
25EVRC012 RC 181219 6721141 449 -60 270 154
Page 11
APPENDIX 2: JORC CODE, 2012 EDITION - TABLE 1
JORC Code, 2012 Edition – Table 1 report template
Section 1 Sampling Techniques and Data
(Criteria in this section apply to all succeeding sections.)
Criteria JORC Code explanation Commentary
Sampling
techniques
• Nature and quality of sampling (eg cut
channels, random chips, or specific
specialised industry standard
measurement tools appropriate to the
minerals under investigation, such as down
hole gamma sondes, or handheld XRF
instruments, etc). These examples should
not be taken as limiting the broad meaning
of sampling.
• Include reference to measures taken to
ensure sample representivity and the
appropriate calibration of any
measurement tools or systems used.
• Aspects of the determination of
mineralization that are Material to the
Public Report.
• In cases where ‘industry standard’ work
has been done this would be relatively
simple (eg ‘reverse circulation drilling was
used to obtain 1 m samples from which 3
kg was pulverised to produce a 30 g charge
for fire assay’). In other cases more
explanation may be required, such as
where there is coarse gold that has
inherent sampling problems. Unusual
commodities or mineralization types (eg
submarine nodules) may warrant
disclosure of detailed information.
Catalina Resources completed 8 RC holes
for 1521 m at the Central Yilgarn project
over the period 1st to 19th December 2025.
Drilling was supervised and samples
collected by geologists from Apex
Geoscience which is an independent
geological consultancy.
Drill samples were collected by Reverse
Circulation (RC) drilling. Drill hole details
are provided in Appendix 1.
RC drilling was used to obtain 1m samples
using a Sandvik Static Cone Splitter in calico
bags and weighing 2 to 3 kg each. Samples
were delivered to the ALS Lab in Kalgoorlie
(for photon assay).
The samples were analysed using the
photon assay method which uses a 0.5kg
sample and requires minimal handling. The
samples are riffle split at the lab and
crushed to 80% passing 2mm to ensure
homogeneity as uniform sample distribution
is important to a quality analysis.
The samples are considered to effectively
represent the drilling at the point of
collection. Sampling included Catalina
Resources standard QAQC procedures.
Quality control of the assaying comprised
the collection of a duplicate samples every
hole, along with regular insertion of industry
(Geostats) standards (certified reference
material) and (certified reference material)
and blanks.
Drilling
techniques
• Drill type (eg core, reverse circulation,
open-hole hammer, rotary air blast, auger,
Bangka, sonic, etc) and details (eg core
diametre, triple or standard tube, depth of
Reverse Circulation (RC) drilling was
performed by McKay Drilling from Perth,
using a 5.25-inch diameter drill bit with 6 m
Page 12
Criteria JORC Code explanation Commentary
diamond tails, face-sampling bit or other
type, whether core is oriented and if so, by
what method, etc).
length drill rods with automatic rod handlers.
Holes were drilled at an angle of -60⁰.
An 8x8-mounted Schramm 685 RC drill rig,
supported by a Mercedes 8x8 booster truck, a
Sullair 900/1150 auxiliary compressor and a
Hurricane 1000-psi booster, was used to
complete the drilling program.
RC drilling produces dry rock chips, as large
capacity air compressors dry the rock out
ahead of the advancing drill bit.
Downhole Surveys employed a downhole
Gyro making readings every 5m.
Drill sample
recovery
• Method of recording and assessing core
and chip sample recoveries and results
assessed.
• Measures taken to maximise sample
recovery and ensure representative nature
of the samples.
• Whether a relationship exists between
sample recovery and grade and whether
sample bias may have occurred due to
preferential loss/gain of fine/coarse
material.
Sample recovery was assessed visually via
the sample size collected into the calico
bags. Where sample recovery was low due to
wet samples material was scooped from the
spoil pile.
Sample recovery and condition was noted for
every metre.
Ground water caused wet samples
occasionally, so splitting of the sample was
not possible.
In ground sumps were dug prior to drilling
commencing, to collect the excess
groundwater expelled by the rig.
Catalina Resources does not anticipate any
sample bias from loss/gain of material from
the drill rig cyclone.
Logging
• Whether core and chip samples have been
geologically and geotechnically logged to a
level of detail to support appropriate
Mineral Resource estimation, mining
studies and metallurgical studies.
• Whether logging is qualitative or
quantitative in nature. Core (or costean,
channel, etc) photography.
• The total length and percentage of the
relevant intersections logged.
RC drill holes were logged for various
geological attributes, including colour,
lithology, oxidation, alteration, mineralisation
and veining. All holes were logged in full by
geologists from Apex Geoscience.
No geotechnical logging was possible as the
RC drilling method does not allow RQD
recording.
Geological logging was qualitative at 1m
intervals and was recorded at the sample
depth.
Representative 1m samples weighing 20 gms
were collected and placed into plastic chip
trays for later reference.
The recording was done at a level
commensurate with the early stage of
exploration.
Page 13
Criteria JORC Code explanation Commentary
Sub-
sampling
techniques
and sample
preparation
• If core, whether cut or sawn and whether
quarter, half or all core taken.
• If non-core, whether riffled, tube sampled,
rotary split, etc and whether sampled wet
or dry.
• For all sample types, the nature, quality
and appropriateness of the sample
preparation technique.
• Quality control procedures adopted for all
sub-sampling stages to maximise
representivity of samples.
• Measures taken to ensure that the
sampling is representative of the in situ
material collected, including for instance
results for field duplicate/second-half
sampling.
• Whether sample sizes are appropriate to
the grain size of the material being
sampled.
N/A
Dry and wet drill samples were collected at the
drill collar. After passing through the sample
hose and into the drill cyclone the samples
pass through a riffle splitter to homogenise the
sample and to nullify the effects of particulate
gold. After splitting, the sample was collected
in a calico bag, ready for assaying.
The samples are considered to effectively
represent the rock at the point of collection.
Sampling included Catalina Resources
standard QAQC procedures. Quality Control
on the RC drill rig included insertion of
duplicate samples to test lab repeatability,
insertion of standards to verify lab assay
accuracy and cleaning and inspection of
sample assembly. A standard or duplicate was
inserted every 20th to 25th sample.
The sample sizes and analysis size are
considered appropriate to correctly represent
the mineralisation based on the style of
mineralisation, sampling methodology and
assay value ranges for the commodities of
interest.
Quality of
assay data
and
laboratory
tests
• The nature, quality and appropriateness of
the assaying and laboratory procedures
used and whether the technique is
considered partial or total.
• For geophysical tools, spectrometers,
handheld XRF instruments, etc, the
parameters used in determining the
analysis including instrument make and
model, reading times, calibrations factors
applied and their derivation, etc.
• Nature of quality control procedures
adopted (eg standards, blanks, duplicates,
external laboratory checks) and whether
acceptable levels of accuracy (ie lack of
bias) and precision have been established.
All samples were delivered to the ALS Labs in
Kalgoorlie for Photon Assay. Photon assay
method has shown to provide quick turn
around times and high accuracy.
The assay method and laboratory procedures
were appropriate for this style of
mineralisation. The fire assay technique for the
RC chips were designed to return precise
precious metal recoveries.
The ALS lab inserts its own standards and
blanks at set frequencies and monitors the
precision of the analyses. As well, the lab
performs repeat analyses at random intervals,
which return acceptably similar values to the
original samples.
Laboratory procedures are within industry
standards and are appropriate for the
commodities of interest.
Industry certified Geostats standards were
inserted in the RC chip sample stream every 25
Page 14
Criteria JORC Code explanation Commentary
samples, and field duplicates were collected
every 20 samples.
The samples are considered to effectively
represent the rock at the point of collection.
Sampling included Catalina Resources
standard QAQC procedures.
Verification
of sampling
and assaying
• The verification of significant intersections
by either independent or alternative
company personnel.
• The use of twinned holes.
• Documentation of primary data, data entry
procedures, data verification, data storage
(physical and electronic) protocols.
• Discuss any adjustment to assay data.
Consultant geologists, from Apex Geoscience,
were involved in the logging of the RC drilling.
Apex was involved in the whole process
including drill hole supervision, chip sample
collection and importing of the completed
assay results. Drill hole logs were inspected to
verify the correlation of mineralized zones
between assay results and
lithology/alteration/mineralisation. The entire
chain of custody of this recent drilling was
supervised by Apex Geoscience.
The drill hole data was logged in a locked excel
logging template and then stored in a
Micromine database structure for long term
storage and validation.
Data was reported by the laboratory and no
adjustment of data was undertaken.
All assay results were verified by alternative
company personnel and the Qualified Person
before release.
Analysis of the accuracy of the above QAQC
procedures needs to be within acceptable
limits.
Location of
data points
• Accuracy and quality of surveys used to
locate drill holes (collar and down-hole
surveys), trenches, mine workings and
other locations used in Mineral Resource
estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic
control.
RC drill hole locations were picked up using a
handheld Garmin GPS, considered to be
accurate to ± 5 m.
Downhole surveys have been completed at 5
m stations (and start and end of hole) using a
downhole gyroscopic survey tool.
All coordinates were recorded in MGA Zone
51 datum GDA94.
Topographic control is provided by a Digital
Terrain Model based on the 90 m Shuttle
Radar Topographic Mission data.
Drill hole details are in Appendix 1 of this
announcement.
Page 15
Criteria JORC Code explanation Commentary
Data
spacing and
distribution
• Data spacing for reporting of Exploration
Results.
• Whether the data spacing and distribution
is sufficient to establish the degree of
geological and grade continuity appropriate
for the Mineral Resource and Ore Reserve
estimation procedure(s) and classifications
applied.
• Whether sample compositing has been
applied.
Drill holes were sited in a position to
intercept the previously identified air core
mineralisation, aiming to obtain grade and
width information.
The orientation of the mineralisation is not
yet defined, at this stage of exploration.
N/A as no resource estimate is made.
RC drilling was on line spacing at 100m or
200m and 75m inbetween drill holes.
Deviations from the 75m spacing occurred
where necessary to avoid restricted zones.
No compositing has been conducted.
Orientation
of data in
relation to
geological
structure
• Whether the orientation of sampling
achieves unbiased sampling of possible
structures and the extent to which this is
known, considering the deposit type.
• If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to
have introduced a sampling bias, this
should be assessed and reported if
material.
Appendix 1 tables the MGA coordinates, of
each hole.
RC drilling is a hammer percussion technique
to shatter the rock and does not all
Share your feedback
Discover